Tuesday, December 20, 2016

Merry Christmas and Happy New Year

Christine and I would like to take this opportunity to wish everyone a "Merry Christmas and a Happy New Year".



I would also like to give a big thank you to those modellers who bought items from my Signals branch shop over the past year and particularly during the recent 25% off sale from Shapeways.

Once again I am going to post about my recent 3D printing efforts and I hope that this isn't too annoying or boring. I will try to return soon to more posts about my Bylong layout and the related things that I have been doing.

Here are the most recent additions:

NSWGR Platform Level Signal Box
Platform Level Signal Box
NOTE: Camera lens distortion evident here, it is not the signal box
This is a rusticated weatherboard platform level signal box 17 feet 8 inches long that has been designed based on the signal box once at Kankool. The Greg Edwards S3 Data Sheet was used for dimensions along with photographs of Kankool signal box. The door of this signal box is at the left hand end as per Kankool.

Platform Level Signal Box 3D Printed Parts
A set of detail parts in Frosted Ultra Detail acrylic material is required to complete this signal box. Included in the detail parts are two different doors, windows, water tank, downpipe, gutter and a timber beam fitted with 8 electrical insulators.

Signal Box Left Hand Door Detail Set
There is a Left Hand Detail Set with the correct left hand doors, it is about where the hinges and door knobs are and that the door would be hinged on the end wall.

The walls and roof are one piece in the White Strong and Flexible (WSF) material that has a fine 'sandy' surface that needs to be sprayed with several coats of Auto Primer Filler or Auto Spray Putty and then rubbed back with about 1500 grit Wet and Dry paper to smooth the surface. It is up to the modeller to sand between coats or after several coats. Be careful not to sand the any detail away, particularly the corrugations in the roof. The corrugations could be brushed along their length while the paint is wet to stop the corrugations from filling with paint.

There is also walls and roof available in Frosted Ultra Detail which only needs to be rinsed in some acetone for a couple of minutes prior to painting. This is to remove any last traces of the waxy support material from the printing process.

Paint with the final colours either in the NSWGR 'Stone' colour scheme or the later pastel colour scheme (usually pale green blue or cream with white trim).

Please note that the model pictured is the WSF version and it has only has one coat of primer followed by the final colours to depict a perhaps more 'normally' finished model and not the multiple coats of primer and rubbing back to smooth the surface that some modellers may do.

The signal box is also available with the door at the right hand end and a right hand set of details parts are available for this signal box.

A pair of small water tanks with downpipes from this detail set is also available separately.
Small Water Tanks from Signal Box Detail Parts
Early NSWGR Rivetted Water Tank
Rivetted Water Tank front view

Rivetted Water Tank showing bolted flanges on inside.
The rivetted water tank consists of the four water tank sides printed as one piece. The interior flanges and bolts have been included in the print.

A ledge has been printed inside the tank for a 3mm thick floor, layers of polystyrene or 3mm MDF would be suitable. Measure the underside of the tank for the floor, it should be 88.5mm x 88.5mm.

The tank is printed in the White Strong and Flexible (WSF) material which has a fine 'sandy' surface that needs to be sprayed with several coats of Auto Primer Filler or Auto Spray Putty and then rubbed back with about 1500 grit Wet and Dry paper to smooth the surface. It is up to the modeller to sand the flat areas between coats or after several coats. Be careful not to sand the rivets.

The water tank pictured is sitting on a Laser Rail Bits timber stand kit. An alternative would be the Models 'N More version.

Please note that the model pictured has only has one coat of primer followed by the final colours to depict a perhaps more 'normally' finished model and not the multiple coats of primer and rubbing back to smooth the surface that some modellers may do.

Recently released is a steam dome for the Eureka Models NSWGR D50 Class steam locomotive along with a Eureka Models replacement D50 funnel and dome set.
Eureka Models NSWGR D50 Funnel and Steam Dome set
Also recently released are NSWGR C32 and Standard Goods (D50, D53 and D55 Class) funnels and steam dome sets with 1/8th inch mounting pegs that can be used to upgrade a DJH model locomotive or perhaps an early brass model.

These have been released in both HO and 7mm Scale.
C32 Funnel and Steam Dome - Standard means HO 1/8 inch and 7 mm Scale 1/4 inch mounting peg

Standard Goods (D50, D53 and D55 Class) Funnel and Steam Dome set

The detail advantage of the 3D printed funnels is that they have the bolts on the flange holding the funnel to the smokebox of the locomotive. It is not possible to have the bolt heads on injection moulded funnels as the funnel would not be able to be removed from the moulding die. The only other way to get the bolts on the model funnel is to split the funnel into two parts as per the Ixion C32 which then leaves a fine groove/line at the join.

Lastly for those who model in N Scale (1:160) I have C32 and D50 funnel and steam dome sets available.
N Scale C32 Funnel and Dome set

N Scale Standard Goods (D50, D53 and D55 Class) Funnel and Dome set






2 comments:

DavidV said...

The signal box looks great. Have you considered doing some sprues of the 6 pane windows? Maybe a double width window like the one at Wingello? The doors and windows will also be a great asset to improving the various laser cut models out there.

Ray P said...

David

A quick and simple answer, yes, planned for.

I will release the various details as multiples, windows, doors, insulator bars for other buildings, etc.


Ray